Com-Central.net

Shadow_Banshee · ***Power User*** Offline Joined: Feb 03, 2005 Posts: 575

damn, theres lots of guys out there not showing second vid cards on these boards and asus are replying with its not faulty boards , so it has to be the bios. phone asus support Homey ....... hey kit you have 4 cards on your system? i thought you built a twin?

Shadow_Homfixr · Posted: Sun Nov 12, 2006 3:19 pm Post subject: Re: bodge it!

Never mind everybody... I hosed the BIOS Evil or Very Mad

updating to version 0402. Followed the directions giv'n by ASUS and put 0402 on disc then went into BIOS . There is a ASUS flash utility there. It found the .bin file and started it's thing by erasing the version there them Murphy showed his ugly a** and warning message came up could not read the current file and all died....well video did and I'm sure a few other things also Twisted Evil

. Guess this is gonna cost me a new mobo and a lot of embarrassment no to mention the time invested. Gonna try to send this mobo back but they prolly will not refund or replace. Thanks for all the help guys!! I'll let ya'll know the outcome.

Kitform · Posted: Sun Nov 12, 2006 3:00 pm Post subject: Re: bodge it!

I thought the forceware drivers 91.45 are only for the quad graphics set up.

Asus use a jumperless mobo, you can swap between SLI mode in software from the desktop, unlike other mobo's where you have to do it hardware and reboot.

If it was only a software issue then it should still show in device manager.

IMHO

Mr. Green

My device manager screen

Shades · Posted: Sun Nov 12, 2006 1:39 pm Post subject: Re: bodge it!

lol
Good find.

Shadow_Banshee · ***Power User*** Offline Joined: Feb 03, 2005 Posts: 575

yeah hes got the bridge in place, but i think its still a unactivted dual mode prob i found this on a faq about sli not enabling on that board "Please update ASUS M2N-SLI Deluxe BIOS to v0402 or later and nVidia Forceware VGA driver to v91.42 or later to solve this problem.
" i'm almost certain that the forceware on homeys disc is lower version than that!
FIX IT MR! 4am is killin me

Shades · Posted: Sun Nov 12, 2006 12:48 pm Post subject: Re: bodge it!

Reading Ban's last post made me think of something else, doesn't SLi have a little 'bridge' you have to clip onto the top of the two cards?
I know it did when it first came out.
May have been a 'spare' part supplied with the mobo.

Shadow_Banshee · ***Power User*** Offline Joined: Feb 03, 2005 Posts: 575

i still think its a setting, like single or dual mode, older mainboards have a a little card that you switch round to enable dual mode, maybe theres a software or bios option for this on your card that you are missing or even a jumper on the mainboard,
chances are that the mainboards set in single mode.

Shades · Posted: Sun Nov 12, 2006 10:10 am Post subject: Re: bodge it!

Yeh, sounds like the board to me.
Getting a lot of faulty boards on my BYO community forum as well.
Is all very well saving money by having the things made by slave labour but their quality control's pants!
Strangely, the replacement board's usually fine.

Kitform · Posted: Sun Nov 12, 2006 9:42 am Post subject: Re: bodge it!

With the latest Forceware drivers loaded and a bios upgrade, I'd be suspecting a faulty mobo since it doesn't show in device manager.

Shadow_Homfixr · Posted: Sun Nov 12, 2006 4:06 am Post subject: Re: bodge it!

Ok the thing is built and everything powered up BUT it will not see the second card!! Banshee and Mike and another fellow I know went thru most all everything a couple times and still no SLI config. The puter just ain't seeing the second card in the 2nd PCI-E slot and neither is Device manager. The fan on the card is running so it has power. Uninstalled and reinstalled hardware and software numerous times, updated all software at least twice, updated the BIOS. Couldn't find anything in BIOS to change but plug and play was off....now on. Switched cards...both work fine. Tried one card at time in each slot and got no video at all out of the black slot which is the secondary PCI-E slot. Banshee says it gotta be software or a setting but I'm slowly coming to the conclusion that I have a bad MB....maybe not so slow....lol. Dang Murphy will someone please shoot him for me....lol. Any thought would be greatly appreciated. I'll be on MSN most of the day tomorrow so please HELP!!!!!!!!!!!!!!

Kitform · Posted: Fri Nov 10, 2006 2:16 pm Post subject: Re: bodge it!

- Shadow_Homfixr

I'm gonna wait until tomorrow night to plug it into the wall and and see what does or doesn't happen...

*Note to self*...Check standby generator for diesel.

P.S. Can I have onions on my dog Homey.

Mr. Green

Shadow_Bshwackr · Posted: Fri Nov 10, 2006 12:08 pm Post subject: Re: bodge it!

The trick is to be prepared Homey! Get the hotdogs ready and 'plug 'r in!' If you see fire, roast up those hotdogs! If not, you're on the way to having a new 'puter....LOL

Shades · Posted: Fri Nov 10, 2006 8:41 am Post subject: Re: bodge it!

- Shadow_Homfixr

I'm gonna wait until tomorrow night to plug it into the wall and and see what does or doesn't happen.

LMAO!
I was so nervous about my first build I couldn't bring myself to powering it up for a week!
'Birds of a feather'.
Wink

401RCAF_HitMan · Posted: Fri Nov 10, 2006 12:53 am Post subject: Re: bodge it!

fingers are crossed for ya bud... Shocked

Shadow_Homfixr · Posted: Fri Nov 10, 2006 12:31 am Post subject: Re: bodge it!

LOL Hitman your prolly right about that now a days! The final parts arrived today and I had a little head start from what I received yesterday and already had. I finish putt'n everything in the new case tonight and hoping I hooked everything up to it's proper place and not left anything out...lol! I am so tired from stressing out about mess'n something up I'm gonna wait until tomorrow night to plug it into the wall and and see what does or doesn't happen...lol. For now it's off to bed for another sleepless night from dreaming about building this nightmare...LOL.

Com-Central.net

Select Language

Login

`±`Recent Visitors

`±`User Info-big

Archive Revive
Username:
This is an archived topic - your reply will not be appended here. Instead, a new topic will be generated in the active forum. The new topic will provide a reference link to this archived topic.

Com-Central.net

Select Language

Login

±Recent Visitors

±User Info-big

`±`Recent Visitors

`±`User Info-big